Plot to a plotter that's connected to a small networked device — typically a Raspberry Pi — instead of cabling the plotter to the machine you design on. Plottter sends the job over your network; the device drives the plotter. Your computer is then free during long plots, and the plotter can live wherever is convenient (another room, a shelf) without a computer tethered to it.
This is the device side of a companion project, plottter-daemon — a small
stdlib-only HTTP service that receives jobs and drives the plotter with pyaxidraw. It
lives in its own repository; see its README.md for full Raspberry Pi setup. This guide
covers using the feature from Plottter.
Works with any AxiDraw-compatible plotter (AxiDraw, Uunatek iDraw H SE, etc.) — the same hardware the Direct AxiDraw Control path supports.
Your computer (Plottter) Raspberry Pi (plottter-daemon)
Plot with AxiDraw ──HTTP (LAN/Wi-Fi/VPN)──▶ receives SVG + settings
(device set in Preferences) drives the plotter via pyaxidraw
polls status, shows progress ◀─────────── plots autonomously
- The daemon owns the job. Once a plot starts it runs inside the daemon, so you can disconnect, put your computer to sleep, or leave the network — the plot keeps going.
- One job at a time, with pause / resume / stop and live progress, exactly like the USB dialog.
- Your design is never altered. The daemon plots the SVG verbatim with path reordering disabled — all optimization happens in Plottter.
- Feature parity with USB. Pen up/down calibration, plotting, pause/resume, and multi-layer pen-swap all work over the network.
Full instructions are in the plottter-daemon project's README.md. In short, on a
Raspberry Pi (or any always-on Linux host) connected to the plotter by USB:
# in the plottter-daemon folder, on the Pi
python3 -m venv .venv && . .venv/bin/activate
pip install -e .
pip install https://cdn.evilmadscientist.com/dl/ad/public/AxiDraw_API.zip
python -m plottter_daemon --device-name "iDraw H SE A2" # prints a token to copy- It listens on port 8080 by default and prints an access token (paste it into
Plottter). Use
--no-authinstead if you don't want a token on a trusted home network. - Make sure the Pi user can reach the serial port (
groupsshould includedialout). - Run it under systemd (
deploy/plottter-daemon.service) so it starts on boot and you never need an SSH session open.
Confirm it's reachable without hardware first by running with --fake --no-auth and
connecting from Plottter (below) — handy for testing the network path.
Open Edit → Preferences and find the Remote Plotter group:
- Device URL —
http://<pi-host-or-ip>:8080(e.g.http://plotter.local:8080, a LAN IP, or a Tailscale name — anything reachable). - Token — paste the token the daemon printed (leave blank if you ran it
--no-auth). - Tick Enable remote plotting, then click Test Connection to confirm the daemon is reachable. Click OK to save.
These settings are remembered between sessions. Untick Enable remote plotting any time to plot locally over USB instead.
Now open Plot with AxiDraw. The connection indicator at the top tells you what's connected:
- ● Connected via network — <device> → plotting goes to the Pi.
- ● Connected via USB — <device> → remote plotting is off (or unreachable), so it falls back to a USB-connected plotter.
Hit Refresh in the dialog to re-check the connection after starting the daemon or changing the Preferences.
Set the model. The job carries your Model selection (e.g. AxiDraw SE/A2 for the iDraw H SE A2), so set it the same as you would for USB — that's what tells the daemon the plot-bed size.
Everything in the dialog now talks to the remote plotter:
- Calibrate with Raise Pen / Lower Pen — these go over the network to the real plotter, so set your pen-up/down positions just as you would over USB.
- Plot Now sends the job. Progress updates as it plots; you can then disconnect or step away — the Pi finishes the plot on its own.
- Pause / Resume and Stop work mid-plot. Stop also clears the job on the device, so
use it (rather than just closing) when you don't intend to resume. While a plot is paused
the manual controls work too, so you can fix or re-seat a pen and re-tune its height before
resuming — see Fixing a pen mid-plot. This
needs a daemon from 2026-10-16 or later (
git pull+ restart the service on the Pi); an older one refuses the commands and the dialog tells you to update it. - Multi-color (pen swap): with "Pause between layers" enabled, each layer is sent as its own job and you're prompted to swap the pen between them — you'll need to be present for the swaps, as with USB. The manual controls work during a swap, so you can tune each pen's height before continuing (see Swapping pens between layers).
Because the device owns the job, a brief Wi-Fi blip is invisible — Plottter keeps following the plot once the connection returns. If the connection drops for longer, the plot keeps running on the device and the dialog treats it as paused so you can pick it back up.
To reconnect, just reopen Plot with AxiDraw (or hit Refresh). If the device still has a job, the dialog detects it and offers to Resume (if it paused) or Stop it — so a plot left paused after a disconnect never strands the plotter as "busy." You should no longer need to restart the daemon to get unstuck. If you ever do see a busy message starting a new plot, Plottter will offer to stop the leftover job for you.
Auth is optional and independent of how your network is set up (LAN, VPN, Tailscale — the URL field accepts any of them):
- The daemon can require a bearer token on all control endpoints;
/healthstays open so Plottter can detect it. Paste the token into the Token field. - On a trusted home network you can run the daemon with
--no-authand leave the token blank. - The daemon physically moves hardware, so don't expose it directly to the public internet — keep it on your LAN/VPN.
Status shows "No plotter daemon reachable at …".
- Is the daemon running on the Pi? (
systemctl status plottter-daemon, or check your terminal.) - Is the URL right, including
http://and:8080? Try the Pi's IP instead of its hostname. - Can your computer reach the Pi at all?
ping <pi-ip>. Same network / VPN?
Connected, but plotting errors with "Plotter not found".
- On the Pi, confirm the plotter enumerated:
ls /dev/ttyUSB*(anddmesg | tailafter plugging in). Make sure the daemon's user is in thedialoutgroup. - If a port exists but auto-detect fails, start the daemon with
--serial-port /dev/ttyUSB0.
"The remote plotter is busy."
- One job at a time. Wait for the current plot to finish (or Stop it) before sending another.
The plot kept going after I disconnected.
- That's by design — the daemon owns the job. Use Stop (or the plotter's physical pause) to halt it.
See also Direct AxiDraw Control for the
USB path and the shared pen/speed settings, and the plottter-daemon README for Pi-side
setup and systemd.